BREEDLOVE MOUNTS

          Heavy Duty Antenna Mounts for Mobile Ham Radios   $10 Flat rate Shipping  with Satisfaction Guaranteed !

But if all you have is a cup in the bottom then I can custom make you one with longer wedges to catch the cup and around the top.   Just give me the measurements needed for construction.

Pocket bracket with Pedestal mount and ring terminal connection with a 3/8-24 top thread for the antenna.

Model # 921   $ 80.00

pocket bracket with an NMO to ring terminal mount

Model # 927   $ 80.00

pocket bracket with an NMO to SO-239 connection

Model # 928   $ 80.00

The solid brass fold over also works as a quick disconnect.  One turn lays the antenna over and about 3 more takes it off.


Extra nuts to use multiple antennas on the one mount are available on the accessories page.

Fits a pocket 1-3/8 to 2-1/8 inches wide and any length.                                          The 5/8 inch mounting hole is 4-1/2 inches from the center of the pocket.
Stainless steel bolts

The top plate is 1/4 thick by 2-1/4 inches wide
The top screws are counter sunk and the edges rounded off 
The wedges extend 4-1/2 inches long down into the pocket
Strong enough for a 10lb. antenna 

The solid aluminum pedestal mount is 1-1/2 inches in diameter and has the 3/8-24 threaded hole in the top for your antenna.    The SO-239 connector cannot pull apart and will hold any size antenna you put on the mount. 

pocket bracket with Quick disconnect mount and ring terminal connection

Model # 923  $ 90.00

          HOW TO INSTALL AND REMOVE STAKE POCKET BRACKET

Installation is a series of steps, quick and simple.
Loosen the four outside bolts but only 1/4 to 1/2 turn, don’t need much.
Adjust the bracket to it's smallest size.
If the bracket is to large for the stake hole, then remove one or both expansion
plate attached to wedge.  The plate is required for the new extra-large
trucks made today and is not required on most trucks.
   Pick the hole you want and direction to face ( inboard or out) and start
tightening the center screw.  As the bracket starts to tighten, wiggle
the it around so it will settle into the shape of the stake hole.
Continue tightening until satisfied.     As you tighten all of the pressure is      
contained in the top plate.  There is no downward  pressure onto the     
truck bed at all.  Tighten down the four outside bolts to totally secure the top plate.
   After the bolts are tight, grab hold of plate and give one last hard shake.
If anything moves, tighten the center bolt some more.  It will not be

necessary to loosen the outside bolts at this point, but instead check
that they are still tight after tightening the center.


   Removal is just as easy but requires a hammer or something like it.

Loosen the four outside bolts but only 1/2 turn, don’t need much.
Unscrew the center screw until it sticks up about 3/4 of an inch or so.
Tap on the screw until it goes down with however much force it takes,
which in most cases has proven to be not that much.
The bracket will lift straight up and out of the hole with no problem.  If still
tight simply loosen the center screw more to make the bracket smaller.
    Also if for some reason it was needed, ( bed liner, etc.) the mount plate can be as much as
1/2 inch above the truck bed and still work.   

 

pocket bracket with Pedestal mount and SO-239 connection

Model  # 922   $  105.00

Extended camper top stake pocket bracket.   This bracket is 6 inches between the center of the pocket and the antenna.  Any of my mounts can be used.  


Model # 919    $ 65.00   

pocket bracket with Quick disconnect mount and SO-239 connection

Model # 924   $  115.00

pocket bracket with a fold over mount and SO-239 connection

Model  # 926  $ 120.00

Extra Quick disconnect nuts and centers are available on the accessories page To use different antennas' on the one mount.  All have the 3/8-24 thread in the top. 

These pocket brackets use and expanding wedge action to lock into the pocket.  So it is Necessary for the pocket to have side walls down inside.  If your pocket has open space and a cup in the bottom, then this bracket will not work for you. 

pocket bracket with a fold over mount and ring terminal connection.  3/8-24 top thread for the antenna 

Model  # 925   $  95.00