Fits a pocket  1  1/2 inches to 1 3/4 wide                            2-1/4 inches to 2 5/8 inches long,

The top plate is 3/8 inch thick and 2-1/4 inches wide

1/4 inch Stainless steel counter sink bolts

5/8 inch hole for the antenna mount

A ground screw is located on one of the clamps

EZN stake pocket bracket SHORT

Fits a pocket only 2 inches long

Model # 930  $  35.00

EZN stake pocket bracket   LONG

Fits a pocket 2-1/4 to 2-5/8 inches long

Model  # 910   $ 35.00

Large vertical stake pocket bracket
Model # 703     $ 75.00.

The box is 3 inches square aluminum and sits on top of the bedrail.  5 inches long at the base and 3 inches long on top.

 Fits a pocket  1-1/2 inches to 1 3/4 inches wide                                 2 inches long
4 Degree angle cut into the top plate to make the antenna vertical
The top plate is 1/2 inch thick and 2-1/4 inches wide
1/4 inch Stainless steel counter sink bolts
5/8 inch hole for the antenna mount
A ground screw is located on one of the clamps

‚Äč        BREEDLOVEMOUNTS

          Heavy Duty Antenna Mounts for Mobile Ham Radios   $10 Flat rate Shipping  with Satisfaction Guaranteed !

EZN stake pocket bracket LONG 4 degree top plate

Fits a 2-1/4 by 2-5/8  hole

For leveling the bed rail

Model # 940   $ 40.00

 Fits a pocket that is 1-1/2 inches to 1 3/4 inches wide                           2-1/4 inches  to 2 5/8 inches long

 4 Degree angle cut into the top plate to make the antenna vertical
The top plate is 1/2 inch thick and 2-1/4 inches wide
1/4 inch Stainless steel counter sink bolts
5/8 inch hole for the antenna mount
A ground screw is located on one of the clamps

Heavy Duty Stake pocket bracket  

Model # 900     $50.00

Fits a pocket 1 1/2 inches to 1 3/4 inches wide                                 2 inches long,
The top plate is 3/8 inch thick and 2-1/4 inches wide
1/4 inch Stainless steel counter sink  bolts
5/8 inch hole for the antenna mount
A ground screw is located on one of the clamps

 If you have a pocket with a cup in the bottom .No side walls. I can custom make a bracket with longer wedges .  Go to the custom order page and give me the measurements needed for construction.

EZN stake pocket bracket SHORT 4 degree top plate

Fits a pocket that is only 2 inches long

For leveling the bed rail

Model # 950   $  40.00

Vertical stake pocket bracket with a pedestal mount and ring terminal connection

Model  # 960  $75.00

Fits a pocket 1-3/8 to 2-1/8 inches  wide (side to side)

any length (front to back)

the hole for the antenna is 5/8"                                                             4-1/2 inches from the center of the pocket to the antenna hole

Stainless steel   bolts

The top plate is 1/4" thick   2  1/4 " wide                                               Fits under a tool box or camper top           

The wedges are 4-1/2 inches long

 You must have sidewalls down inside the pocket for this bracket to work.


The box is 2-1/2 inches square aluminum   4 inches long at the base and 2 inches long on top. 


PayPal Acceptance Mark

Fits a pocket 1-3/8 to 2-1/8 inches  wide (side to side)

any length (front to back)

the hole for the antenna is 5/8"                                                             4-1/2 inches from the center of the pocket to the antenna hole

Stainless steel hex head  bolts

The top plate is 3/8" thick   2- 1/4 " wide                                                          

The wedges are 4-1/2 inches long

 You must have sidewalls down inside the pocket for this bracket to work.


Camper top stake pocket bracket

Model # 920   $55.00